一、卷簾門設備導軌與方管

1、 Rolling shutter door equipment guide rail and square tube

1、在洞口的兩邊確認導軌與方管設備方位，用錘線放出導軌與方管基準線、放出方管連接件固定螺栓十字線，導軌與方管逾越吊頂不小于20CM。

1. Confirm the orientation of the guide rail and square tube equipment on both sides of the hole, use a hammer line to set out the reference line between the guide rail and square tube, and set out the cross line of the fixing bolts of the square tube connection. The guide rail and square tube should not exceed the suspended ceiling by less than 20cm.

2、用沖擊鉆在墻柱上打出連接件固定脹大螺栓孔，連接件的間隔不得大于600mm，兩頭距方管口100mm。

2. Use an impact drill to punch the expansion bolt holes for fixing the connecting pieces on the wall column. The spacing between the connecting pieces should not exceed 600mm, and the distance between the two ends and the square pipe mouth should be 100mm.

3、先上下固定后再?gòu)?fù)一下導軌的垂直度，每米不得大于5mm，全行垂直度不得逾越20mm，無機布料面嵌入導軌深度（見GB14102-2005）。

3. First fix it up and down, then repeat the perpendicularity of the guide rail. Each meter should not exceed 5mm, and the perpendicularity of the entire line should not exceed 20mm. The depth of inorganic fabric surface embedded in the guide rail (see GB14102-2005).

4、講其余連接件裝在，連接件與方管之間選用電焊，每件連接件與導軌間電焊點不少于5點，電焊的寬度不少于5m，焊接處不應有穿孔現象產生。選用不銹鋼導軌時焊條選用不銹鋼焊條。

4. The remaining connectors are installed, and welding is used between the connectors and the square tube. The welding points between each connector and the guide rail are not less than 5 points, and the width of the welding is not less than 5 meters. There should be no perforation at the welding point. When selecting stainless steel guide rails, stainless steel welding rods should be used.

二、濟南卷簾門設備支承板

2、 Jinan roller shutter door equipment support plate

1、依據大樣圖中的卷軸的規劃中間高度，在立柱或墻上定出動支承板的中間方位，放出脹大螺栓的中間十字線。

1. According to the planned middle height of the scroll in the detailed drawing, determine the middle position of the movable support plate on the column or wall, and release the middle cross line of the expansion bolt.

2、以主支承板中間為基準，昆山自動門廠用水平塑料管找出相對應的從動支承板中間和從動支承板的脹大螺栓孔十字線。

2. Based on the middle of the main support plate, Kunshan Automatic Door Factory uses horizontal plastic pipes to find the corresponding cross lines of the expansion bolt holes in the middle of the driven support plate and the driven support plate.

3、打孔：用沖擊鉆打脹大孔的要求鉆頭垂直于柱面，若單個螺栓孔碰到鋼筋，鉆不進則可恰當移動，但不能影響牢固和外觀。

3. Punching: The requirement for using an impact drill to drill enlarged holes is that the drill bit is perpendicular to the cylindrical surface. If a single bolt hole touches the steel bar and cannot be drilled in, it can be moved appropriately, but it cannot affect its firmness and appearance.

4、裝自動支承板，用螺母、繃簧墊圈，平墊圈把穿過支承板孔的脹大栓旋緊，要求主支承板面垂直于卷軸。

4. Install the automatic support plate, tighten the expansion bolt passing through the support plate hole with nuts, tension spring washers, and flat washers, and ensure that the main support plate surface is perpendicular to the winding shaft.

5、裝從動承板方法同上，但在緊螺栓前，要求用水平管校核從動支承板的中間高度是否與自動承板共同，水平度控制在洞口高度的1/300內，如有差錯及時調整。

5. The method for installing the driven support plate is the same as above, but before tightening the bolts, it is required to use a horizontal tube to check whether the middle height of the driven support plate is the same as the automatic support plate. The levelness should be controlled within 1/300 of the opening height, and any errors should be adjusted in a timely manner.

卷簾門安裝施工技術要求需要注意的事項就如同以上所講解內容一樣，希望能夠給您好的幫助，更多事項就來我們網站http://amazingazon.com咨詢！

The technical requirements for the installation and construction of roller shutter doors need to be noted, just like the content explained above. We hope to provide you with good help. For more information, please visit our website http://amazingazon.com consulting service