遙控卷簾門具有的顯著特點就是快速，這種快速就是體現在其卷簾門的技術含量上，那么，對于卷簾門的使用我們應該注意其特點，這樣才能讓卷簾門得到更好的使用。下面來講講吧。

The remarkable characteristic of remote control rolling shutter door is fast. This speed is first reflected in the technical content of the rolling shutter door. Then, we should pay attention to its characteristics for the use of rolling shutter door, so that the rolling shutter door can be better used. Now let's talk about it.

遙控卷簾門安裝所需要用到的工具和過程

Tools and processes required for the installation of remote control roller shutter door

遙控卷簾門在我們的生活中被廣泛適用于醫藥，倉庫，物流，冷凍品等地方使用，主要起到了防塵，防水，隔熱隔冷，防蟲，防沙灰塵等主要特性。那么，對于遙控卷簾門安裝所需要用到的工具和過程是怎樣的呢？

Remote control rolling shutter door is widely used in medicine, warehouse, logistics, frozen goods and other places in our life. It mainly has the main characteristics of dust prevention, waterproof, heat insulation, cold insulation, insect prevention, sand and dust prevention. Then, what are the tools and processes required for the installation of remote control roller shutter doors?

1、必要工具

1. Necessary tools

角磨機、手槍鉆、水平儀、沖擊鉆，拖線板，轉頭螺絲，螺絲刀、錘子，扳手，腳手架等等。

Angle grinder, pistol drill, level gauge, impact drill, drag line board, swivel screw, screwdriver, hammer, wrench, scaffold, etc.

2、主材料

2. Main material

門簾、導軌、軸承、編碼器，紅外對照，箱罩等主要部分組成。

Door curtain, guide rail, bearing, encoder, infrared contrast, box cover and other main parts.

3、輔助硬件

3. Auxiliary hardware

安裝的必要條件，電源220v，洞口平整等。

Necessary conditions for installation, power supply 220V, hole leveling, etc.

4、出廠前的檢查

4. Pre delivery inspection

對遙控卷簾門進行拆包檢查，查看產品是否有漏件，核對產品出廠單，并開始著手安裝。

Unpack and check the remote control roller shutter door to see if there are any missing parts, check the product delivery order, and start the installation.

作業條件

Operating conditions

1、結構工程施工完畢，粗裝修之后、細裝修之前，好墻面底子灰已完成，面層灰尚未施工前。

1. After the construction of structural works, after the rough decoration and before the fine decoration, the bottom ash of the wall has been completed, and the surface ash has not been constructed.

2、洞口尺寸及埋件位置、數量、規格符合設計要求。

2. The size of the opening and the position, quantity and specification of the embedded parts meet the design requirements.

3、進場產品驗收合格。各部分相互匹配，配件齊全。

3. The mobilized products have passed the acceptance. Each part is matched with each other, and the accessories are complete.

安裝導軌

Install the guide rail

將兩則導軌按線焊牢于墻體預埋件上，施焊前注意吊垂直線檢查導軌安裝部位墻體垂直度，達不到垂直度要求時須加墊鐵調垂直后方可施焊。

Weld the two guide rails on the embedded parts of the wall according to the line. Before welding, pay attention to hanging the straight line to check the verticality of the wall where the guide rail is installed. If the verticality requirement is not met, add a sizing block to adjust the verticality before welding.

調試

debugging

濟南卷簾門廠認為要觀察檢查卷筒體、簾板、導軌和傳動部分相互之間的吻合接觸狀況及活動間隙的勻稱性，然后用手緩慢向下拉動關閉，再緩慢勻速向上拉提到位，反復幾次，發現有阻滯頓卡或異常噪音時仔細檢查產生原因后進行調整，直提拉順暢，用力勻稱為。對電控卷簾門，手動調試后再用電動機啟閉數次，細聽有無異常聲音。

Jinan rolling shutter factory believes that it is necessary to observe and check the contact condition between the drum body, curtain plate, guide rail and transmission part and the symmetry of the movable gap, then pull it down slowly and close it by hand, and then pull it up slowly and evenly to the right place. Repeat it for several times. If there is blocking, jamming or abnormal noise, carefully check the cause and adjust it until the lifting is smooth and the force is even. For the electrically controlled roller shutter door, after manual debugging, use the motor to open and close it several times, and listen carefully for abnormal sound.

卷簾門安裝過程中注意保護洞口周邊裝飾層。安裝后洞口周邊修補抹灰或裝飾罩面時飛濺到卷簾門上的灰漿須及時用濕棉砂擦凈。更多相關注意事項您可以關注我們網站http://amazingazon.com獲取到。

During the installation of roller shutter door, pay attention to protect the decorative layer around the hole. After installation, when repairing the plastering or decorative cover around the hole, the mortar splashed on the roller shutter door must be wiped off in time with wet cotton sand. For more relevant precautions, you can follow our website http://amazingazon.com Get.